Section: System Administration (8)
Updated: October 2011Index
Return to Main Contents
readprofile - read kernel profiling information
This manpage documents version 2.0 of the program.
command uses the
information to print ascii data on standard output. The output is
organized in three columns: the first is the number of clock ticks,
the second is the name of the C function in the kernel where those
many ticks occurred, and the third is the normalized `load' of the
procedure, calculated as a ratio between the number of ticks and the
length of the procedure. The output is filled with blanks to ease
- -a, --all
Print all symbols in the mapfile. By default the procedures with
reported ticks are not printed.
- -b, --histbin
Print individual histogram-bin counts.
- -i, --info
Info. This makes
only print the profiling step used by the kernel. The profiling step
is the resolution of the profiling buffer, and is chosen during
kernel configuration (through `make config'), or in the kernel's
command line. If the
(terse) switch is used together with
only the decimal number is printed.
- -m, --mapfile mapfile
Specify a mapfile, which by default is
You should specify the map file on cmdline if your current kernel
isn't the last one you compiled, or if you keep System.map elsewhere.
If the name of the map file ends with `.gz' it is decompressed on the
- -M, --multiplier multiplier
On some architectures it is possible to alter the frequency at which
the kernel delivers profiling interrupts to each CPU. This option
allows you to set the frequency, as a multiplier of the system clock
frequency, HZ. This is supported on i386-SMP (2.2 and 2.4 kernel)
and also on sparc-SMP and sparc64-SMP (2.4 kernel). This option also
resets the profiling buffer, and requires superuser privileges.
- -p, --profile pro-file
Specify a different profiling buffer, which by default is
Using a different pro-file is useful if you want to `freeze' the
kernel profiling at some time and read it later. The
file can be copied using `cat' or `cp'. There is no more support for
compressed profile buffers, like in
because the program needs to know the size of the buffer in advance.
- -r, --reset
Reset the profiling buffer. This can only be invoked by root,
is readable by everybody but writable only by the superuser.
However, you can make
setuid 0, in order to reset the buffer without gaining privileges.
- -s, --counters
Print individual counters within functions.
- -v, --verbose
Verbose. The output is organized in four columns and filled with
blanks. The first column is the RAM address of a kernel function,
the second is the name of the function, the third is the number of
clock ticks and the last is the normalized load.
- -V, --version
Display version information and exit.
- -h, --help
Display help text and exit.
Browse the profiling buffer ordering by clock ticks:
readprofile | sort -nr | less
Print the 20 most loaded procedures:
readprofile | sort -nr +2 | head -20
Print only filesystem profile:
readprofile | grep _ext2
Look at all the kernel information, with ram addresses:
readprofile -av | less
Browse a `freezed' profile buffer for a non current kernel:
readprofile -p ~/profile.freeze -m /zImage.map.gz
Request profiling at 2kHz per CPU, and reset the profiling buffer:
sudo readprofile -M 20
only works with an 1.3.x or newer kernel, because
changed in the step from 1.2 to 1.3
This program only works with ELF kernels. The change for a.out
kernels is trivial, and left as an exercise to the a.out user.
To enable profiling, the kernel must be rebooted, because no
profiling module is available, and it wouldn't be easy to build. To
enable profiling, you can specify "profile=2" (or another number) on
the kernel commandline. The number you specify is the two-exponent
used as profiling step.
Profiling is disabled when interrupts are inhibited. This means that
many profiling ticks happen when interrupts are re-enabled. Watch
out for misleading information.
/proc/profile A binary snapshot of the profiling buffer.
/usr/src/linux/System.map The symbol table for the kernel.
/usr/src/linux/* The program being profiled :-)
The readprofile command is part of the util-linux package and is
Linux Kernel Archive